[ofa-general] Re: [ewg] OFED 1.2.c-11 is available

Erez Zilber erezz at voltaire.com
Wed Aug 8 06:47:10 PDT 2007


Tziporet,


Can you add the following as a known issue:


"open-iscsi over TCP does not support usage of data digest on RedHat EL/AS 4 up3,
up4 & up5."

Note that this comment should be added to OFED release notes, not to
iSER release notes. This is not an iSER bug (it's a bug in the backport
for open-iscsi).

Thanks,
Erez


Tziporet Koren wrote:

> Hi All,
>
> OFED 1.2.c-11 is available now on the OFA server under:
> _http://www.openfabrics.org/builds/connectx/release/_
> Note: This release supports FW 2.1.000 that is available on Mellanox
> web site for download
>       and FW 2.2.0 that will be released soon
>
> Supported Platforms and Operating Systems
> =========================================
> o CPU architectures:
>         - x86_64
>         - x86
>         - ppc64
>         - ia64
>
> o Linux Operating Systems:
>         - RedHat EL4 up3: 2.6.9-34.ELsmp
>         - RedHat EL4 up4: 2.6.9-42.ELsmp
>         - RedHat EL4 up5: 2.6.9-55.ELsmp
>         - RedHat EL5: 2.6.18-8.el5
>         - SLES10: 2.6.16.21-0.8-smp
>         - kernel.org: 2.6.20.x and 2.6.22.x
>         - SLES10 SP1: 2.6.16.46-0.12-smp (partially tested)
>
> Main changes from OFED 1.2.c-10:
> ================================
> - Merged all 1.2 branch patches to 1.2.c
> - mad: Fix address handle leak in mad_rmpp
> - mlx4
>         - Added support for interrupt moderation for create cq to
> support ipoib.
>         - Display the following device information via sysfs:
> board_id, fw_ver,
>           hw_rev and hca_type. As a result ibstat presenting all entries.
>         - Fixed destroy special QPs.
>         - Fixed the work completion opcode for RDMA_READ operation
> - opensm:
>         - Sets the time a packet can live in the Head of Queue of a
> port that
>           drives a CA port to approximately 1 second.
>         - Number of dropped packets due to HOQ that will stall the CA
> was increased
>          to 7 (instead of 1).
> - IPoIB:
>         - Add interrupt moderation support for IPoIB UD
>         - NAPI is available using a module parameter
>         - Fixed a leak in ipoib_transport_dev_init
>         - Fixed kernel oops in IPoIB download
> - New MVAPICH package (mvapich-0.9.9-1451):
>         - mpirun_rsh fixes:
>           * Check that we do not overflow command line size
>           * better handling for accept
>         - Fix for memory allocations whose size is bigger than 2^31-1
>         - Fix for multiple communicator problem
>         - Fix for MPI_Finalize segmentation fault
> - RDS:
>         - rds_poll() always returns POLLOUT.  If you try to send and get
>           EWOULDBLOCK because the remote receiver is congested then
> you don't get
>           to wait for POLLOUT to be raised before sending again --
> it's always
>           raised.  This is worked around by implementing some kind of
> exponential
>           back-off while retrying the send.  This can be done by
> increasing the
>           timeout given to poll().  At each poll() timeout expiry the
> send is
>           tried again.
>         - Set max send and receive scatter/gather list size to 2 in
> the QP attributes.
>           The second sge used for RDS header.
>         - Added rs_poll_flag to rds_socket structure to indicate the
> back pressure
>           status and send space availability.
>         - Added MODULE_VERSION.
> - ehca:
>         - Added support for RHEL4 up5
>
>
> Tested ULPs
> ===========
> The following ULPs are tested:
> o OpenSM
> o MPI (MVAPICH and Open MPI)
> o IPoIB UD and CM
> o SDP
> o SRP
> o iSER
> o RDS
>
> ConnectX specific known issues and limitations
> ==============================================
> - The following features are not supported:
>   o Resize CQ
>   o APM
>   o SQD
> - To load the driver on machines with 64KB default page size UAR bar
> must be
>   enlarged. 64KB page size is the default of PPC with RHEL5 and
> Itanium with
>   64KB page size enabled.
>   Perform the following three steps:
>   1. Add the following line in the firmware configuration (INI) file
> under the
>      [HCA] section:
>        log2_uar_bar_megabytes = 5
>   2. Burn a modified firmware image with the changed INI file
>   3. Reboot the system
>
>
> Tziporet Koren
> Software Director
> Mellanox Technologies
> mailto: _tziporet at mellanox.co.il_ <mailto:tziporet at mellanox.co.il>
> Tel +972-4-9097200, ext 380
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> ewg mailing list
> ewg at lists.openfabrics.org
> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg




More information about the general mailing list