[openib-general] ping problem with ammasso cards(iWARP interface)

Ravinandan Arakali ravinandan.arakali at neterion.com
Fri Jul 7 11:43:23 PDT 2006


Pradipta kumar,
I had tried krping earlier but same result as with rping.
I believe I am using latest stack since it was checked out from
https://openib.org/svn/gen2/trunk

I will try bumping up debug level on rdma_krping. Do you
want the dmesg output while running rping or krping ?

Ravi

-----Original Message-----
From: Pradipta Kumar Banerjee [mailto:bpradip at in.ibm.com]
Sent: Friday, July 07, 2006 11:37 AM
To: Ravinandan Arakali
Cc: openib-general at openib.org
Subject: Re: [openib-general] ping problem with ammasso cards(iWARP
interface)


Ravinandan Arakali wrote:
> I added -d to rping command. I am not seeing the core dump on
> this run. Following is the output(and it blocks at this point).
>
> openfab2:~ # rping -s -vV -C100 -d -a 0.0.0.0 -p 9999
> ipaddr (0.0.0.0)
> port 9999
> created cm_id 0x804e6e0
> rdma_bind_addr successful
> rdma_listen
>
> openfab:~ # rping -c -vV -C100 -d  -a 17.2.2.102 -p 9999
> ipaddr (17.2.2.102)
> port 9999
> created cm_id 0x506b00
> cma_event type 0 cma_id 0x506b00 (parent)
> cma_event type 2 cma_id 0x506b00 (parent)
> rdma_resolve_addr - rdma_resolve_route successful
>
>
> -----Original Message-----
> From: Steve Wise [mailto:swise at opengridcomputing.com]
> Sent: Friday, July 07, 2006 11:07 AM
> To: ravinandan.arakali at neterion.com
> Cc: openib-general at openib.org
> Subject: Re: ping problem with ammasso cards(iWARP interface)
>
>
> adding -d to rping might give more debug info...
>
> Also if the server side core dumps, please get a stack trace and lets
> see whats up...
>
> Steve.
>
>
> On Fri, 2006-07-07 at 11:04 -0700, Ravinandan Arakali wrote:
>> Hi,
>> I have two systems connected back-to-back with ammasso cards. I have
>> configured and built the libraries and drivers as mentioned in
>>
https://openib.org/tiki/tiki-index.php?page=Install+OpenIB+for+Ammasso1100
>>
>> I can ping on the regular ethX interface but both rping and krping on
> iwarp
>> interfaces fail (no packets sent/received).
>> Following is the configuration:
>> System1:
>> eth interface: 17.1.1.101
>> iwarp interface: 17.2.2.101
>>
>> System2:
>> eth interface: 17.1.1.102
>> iwarp interface: 17.2.2.102
>>
>> On System2 I run
>> # rping -s -vV -C100 -a 0.0.0.0 -p 9999
>>
>> On System1 I run
>> # rping -c -vV -C100  -a 17.2.2.102 -p 9999
>>
>> Sometimes I have noticed that when client is started, the server core
> dumps.
>> Other times, there is no core dump but there's no traffic flowing.

Ravi,
   Did you try with the 'krping' (kernel module) utility ? This is the same
as
'rping' but it's a kernel module instead of a user space application.
Also hope you are using the latest stack.
Also enable debugging for the Ammasso driver (modprobe rdma_krping debug=3)
and
send us the dmesg output.

Thanks,
Pradipta Kumar

>>
>> Any help is appreciated.
>>
>> Thanks,
>> Ravi
>
>
> _______________________________________________
> openib-general mailing list
> openib-general at openib.org
> http://openib.org/mailman/listinfo/openib-general
>
> To unsubscribe, please visit
http://openib.org/mailman/listinfo/openib-general
>
>





More information about the general mailing list