[ofa-general] opensm: Unsupported attribute = 0xFF02
Hal Rosenstock
hrosenstock at xsigo.com
Tue Oct 30 14:01:57 PDT 2007
Kilian,
On Tue, 2007-10-30 at 13:56 -0700, Kilian CAVALOTTI wrote:
> Hi,
>
> I'm trying to use opensm as a standby SM on a fabric where the master SM
> is running on a Cisco SFS-7000D (TopspinOS 2.9.0 releng #147)
>
> The switch (Master SM) logs report the following:
>
> Oct 30 12:08:46 10.0.100.2 ib_sm.x[588]: %IB-6-INFO: Configuration caused by SM role change
> Oct 30 12:08:55 10.0.100.2 ib_sm.x[605]: %IB-6-INFO: Initialize a backup session with Standby SM guid 00:05:ad:00:00:08:cf:0d
> Oct 30 12:09:05 10.0.100.2 ib_sm.x[605]: %IB-6-INFO: Session initialization failed with Standby SM guid 00:05:ad:00:00:08:cf:0d
> Oct 30 12:11:05 10.0.100.2 ib_sm.x[605]: %IB-6-INFO: Session not initiated: Cold Sync Limit exceeded for Standby SM guid 00:05:ad:00:00:08:cf:0d
>
> And the opensm (Standby SM) logs show this:
>
> Oct 30 12:08:45 013321 [95AB1160] -> OpenSM Rev:openib-3.0.13
> Oct 30 12:08:45 013366 [95AB1160] -> OpenSM Rev:openib-3.0.13
> Oct 30 12:08:45 031429 [95AB1160] -> osm_vendor_bind: Binding to port 0x5ad000008cf0d
> Oct 30 12:08:45 033276 [95AB1160] -> osm_vendor_bind: Binding to port 0x5ad000008cf0d
> Oct 30 12:08:46 064757 [45007960] -> Entering STANDBY state
> Oct 30 12:08:55 461419 [4780B960] -> __osm_sm_mad_ctrl_process_set: ERR 3107: Unsupported attribute = 0xFF02
> Oct 30 12:08:55 461482 [4780B960] -> SMP dump:
> base_ver................0x1
> mgmt_class..............0x1
> class_ver...............0x1
> method..................0x2 (SubnSet)
> status..................0x0
> hop_ptr.................0x0
> hop_count...............0x0
> trans_id................0x377df6ce
> attr_id.................0xFF02 (UNKNOWN)
This is a proprietary SM attribute used by Cisco SM. Also, I believe the
Cisco SM supports replication to standby's and that would be via
proprietary means.
> resv....................0x0
> attr_mod................0x1
> m_key...................0x0000000000000000
> MAD IS LID ROUTED
>
> I'm not sure what this ERR 3107 means, is there something I could do about
> it? Is there a way to use OpenSM as a standby SM with a managed switch?
No; SM flavors should not be mixed on a subnet. There are numerous
reasons for this.
-- Hal
> For information, I'm using OFED 1.2 (the Cisco fcs version) and details
> about the HCAs are below:
>
> # ibv_devinfo
> hca_id: mthca0
> fw_ver: 1.2.917
> node_guid: 0005:ad00:0008:cf0c
> sys_image_guid: 0005:ad00:0100:d050
> vendor_id: 0x05ad
> vendor_part_id: 25204
> hw_ver: 0xA0
> board_id: HCA.Cheetah-DDR.20
> phys_port_cnt: 1
> port: 1
> state: PORT_ACTIVE (4)
> max_mtu: 2048 (4)
> active_mtu: 2048 (4)
> sm_lid: 2
> port_lid: 4
> port_lmc: 0x00
>
> Thanks,
More information about the general
mailing list