[ofa-general] [PATCH] opensm/scripts/opensm.conf: remove obsolete config file

[Yevgeny Kliteynik]

This conf file is not used any more and should be removed

Signed-off-by: Yevgeny Kliteynik <kliteyn at dev.mellanox.co.il>
---
 opensm/scripts/opensm.conf |  137 --------------------------------------------
 1 files changed, 0 insertions(+), 137 deletions(-)
 delete mode 100644 opensm/scripts/opensm.conf

diff --git a/opensm/scripts/opensm.conf b/opensm/scripts/opensm.conf
deleted file mode 100644
index 502eea2..0000000
--- a/opensm/scripts/opensm.conf
+++ /dev/null
@@ -1,137 +0,0 @@
-# DEBUG mode
-#  This option specifies a debug option.
-#  These options are not normally needed.
-#  The number following -d selects the debug
-#  option to enable as follows:
-#  OPT   Description
-#  ---    -----------------
-#  0  - Ignore other SM nodes.
-#  1  - Force single threaded dispatching.
-#  2  - Force log flushing after each log message.
-#  3  - Disable multicast support.
-#  4  - Put OpenSM in memory tracking mode.
-#  10.. Put OpenSM in testability mode.
-#  none, no debug options are enabled.
-DEBUG=none
-
-# LMC
-#  This option specifies the subnet's LMC value.
-#  The number of LIDs assigned to each port is 2^LMC.
-#  The LMC value must be in the range 0-7.
-#  LMC values > 0 allow multiple paths between ports.
-#  LMC values > 0 should only be used if the subnet
-#  topology actually provides multiple paths between
-#  ports, i.e. multiple interconnects between switches.
-#  OpenSM defaults to LMC = 0, which allows
-#  one path between any two ports.
-LMC=0
-
-# MAXSMPS
-#  This option specifies the number of VL15 SMP MADs
-#  allowed on the wire at any one time.
-#  Specifying -maxsmps 0 allows unlimited outstanding SMPs.
-#  Without -maxsmps, OpenSM defaults to a maximum of
-#  four outstanding SMP.
-MAXSMPS=4
-
-# REASSIGN_LIDS
-#  This option causes OpenSM to reassign LIDs to all
-#  end nodes. Specifying "REASSIGN_LIDS=yes" on a running subnet
-#  may disrupt subnet traffic.
-#  With "REASSIGN_LIDS=no", OpenSM attempts to preserve existing
-#  LID assignments resolving multiple use of same LID.
-REASSIGN_LIDS="no"
-
-# SWEEP
-#  This option specifies the number of seconds between
-#  subnet sweeps.  Specifying SWEEP=0 disables sweeping.
-#  OpenSM defaults to a sweep interval of 10 seconds.
-SWEEP=10
-
-# TIMEOUT
-#  This option specifies the time in milliseconds
-#  used for transaction timeouts.
-#  Specifying -t 0 disables timeouts.
-#  Without -t, OpenSM defaults to a timeout value of
-#  200 milliseconds.
-TIMEOUT=200
-
-# OSM_LOG
-#  This option defines the log to be the given file.
-#  By default the log goes to /var/log/opensm.log
-#  For the log to go to standard output use OSM_LOG=stdout.
-OSM_LOG=/var/log/opensm.log
-
-# VERBOSE
-#  This option increases the log verbosity level.
-#  The "-v" option may be specified multiple times
-#  to further increase the verbosity level.
-#   "-V" option sets the maximum verbosity level and
-#   forces log flushing.
-#   The "-V" is equivalent to "-vf 0xFF -d 2".
-VERBOSE="none"
-
-# UPDN
-#  This option activate UPDN algorithm instead of Min Hop
-#  algorithm (default).
-#  To switch on UPDN algorithm set UPDN="on"
-UPDN="off"
-
-# GUID_FILE
-#  This option only allowed when UPDN algorithm is activated
-#  It specifies the guid list file from which to fetch the guid list
-#  The file contain in each line only one valid guid
-GUID_FILE="none"
-
-#  This option specifies the local port GUID value
-#  with which OpenSM should bind.  OpenSM may be
-#  bound to 1 port at a time.
-#  If GUID given is 0, opensmd use PORT_NUM parameter.
-#  Without -g (GUID="none"), OpenSM trys to use the default port.
-GUID=0
-
-# OSM_HOSTS
-#  The list of all SM's IP addresses in InfiniBand subnet
-#  Used to handover mechanism
-OSM_HOSTS=""
-
-# OSM_CACHE_DIR
-OSM_CACHE_DIR=/var/cache/opensm
-
-# CACHE_OPTIONS
-#  Cache the given command line options into the file
-#  OSM_CACHE_DIR/opensm.opts for use next invocation
-#  Set to '--cache-options' or '-c' in order to enable
-CACHE_OPTIONS="none"
-
-# HONORE_GUID2LID
-#  This option forces OpenSM to honor the guid2lid file,
-#  when it comes out of Standby state, if such file exists
-#  under OSM_CACHE_DIR, and is valid.
-#  Set to '--honor_guid2lid' or '-x' to enable.
-#  By default this is FALSE. Will be set automatically to '--honor_guid2lid'
-#  if OSM_HOSTS includes list of more then one IP addresses.
-HONORE_GUID2LID="none"
-
-# RCP
-#  This option osed by SLDD daemon for handover mechanism
-#  to copy local cache file to remote computer
-RCP=/usr/bin/scp
-
-# RSH
-#  This option osed by SLDD daemon for handover mechanism
-#  to execute commands on remote computer
-RSH=/usr/bin/ssh
-
-# RESCAN_TIME
-#  This option osed by SLDD daemon for handover mechanism
-#  Time between sweep of sldd daemon in seconds
-RESCAN_TIME=60
-
-# PORT_NUM
-#  This option defines HCA's port number which OpenSM should bind
-PORT_NUM=1
-
-# ONBOOT
-#  To start OpenSM automatically set ONBOOT=yes
-ONBOOT=no
-- 
1.5.1.4