[ofa-general] Multiports single HCA uDAPL program problem

[Jie Cai]

It does fix the problem. Thanks a lot.

Jie

-- 
Mr. Jie Cai
Department of Computer Science
Faculty of Engineering and Information Technology
College of Engineering & Computer Science
CSIT Building (108), North Road
The Australian National University
Canberra ACT 0200 Australia
Email: Jie.Cai at cs.anu.edu.au
Tel: +61-2-61251451
Fax: +61-2-61250010
Web: http://cs.anu.edu.au/~Jie.Cai
Mobile: 0433992958 



Davis, Arlin R wrote:
> This looks like an ARP issue across your IPoIB interfaces. 
>
> Please see section 6 of the uDAPL OFED BKM.
>
> http://www.openfabrics.org/downloads/dapl/documentation/uDAPL_ofed_testing_bkm.pdf
>  
> 6. Multi IB port configuration, IPoIB arp reply issues
>
> When two interfaces running one interface may reply to an ARP
> directed to the other interface on the system. The following
> configuration will cause the interfaces to ignore ARP requests if
> not specifically for their IP address.
>
> Add the following lines to /etc/sysctl.conf
> net.ipv4.conf.all.arp_ignore=1
> net.ipv4.conf.ib0.arp_ignore=1
> net.ipv4.conf.ib1.arp_ignore=1
>
> or use sysctl:
> sysctl -w net.ipv4.conf.all.arp_ignore=1
> sysctl -w net.ipv4.conf.ib0.arp_ignore=1
> sysctl -w net.ipv4.conf.ib1.arp_ignore=1
>
> -arlin
>
>   
>> -----Original Message-----
>> From: general-bounces at lists.openfabrics.org 
>> [mailto:general-bounces at lists.openfabrics.org] On Behalf Of Jie Cai
>> Sent: Thursday, January 29, 2009 10:53 PM
>> To: general at lists.openfabrics.org
>> Subject: [ofa-general] Multiports single HCA uDAPL program problem
>>
>> Hi All,
>>
>> I am kind of noob on IB and uDAPL program. Currently, I am trying to
>> write a program with multirail that utilizes 2 ports on a 
>> single Mallenox
>> ConnectX HCA on both nodes.
>>
>> OFED1.3 has been installed on a SUSE 10.3 linux system.
>>
>> The current problem is that IB connection via uDAPL are very unstable,
>> and sometime the connection can't be established.
>> Error message is usually like:
>>
>> 20350 Server waiting for connect request on port 45248
>> accept: ERR dev(0x61d0e0!=0x61d0e0) or port mismatch(1!=2)
>> 20350 Error dat_cr_accept: DAT_INTERNAL_ERROR
>> 20350 Error connect_ep: DAT_INTERNAL_ERROR
>>
>> The status of both port are active:
>> hca_id:    mlx4_0
>>    fw_ver:                2.3.000
>>    node_guid:            0003:ba00:0100:702c
>>    sys_image_guid:            0003:ba00:0100:702f
>>    vendor_id:            0x02c9
>>    vendor_part_id:            25418
>>    hw_ver:                0xA0
>>    board_id:            SUN0070000001
>>    phys_port_cnt:            2
>>        port:    1
>>            state:            PORT_ACTIVE (4)
>>            max_mtu:        2048 (4)
>>            active_mtu:        2048 (4)
>>            sm_lid:            10
>>            port_lid:        8
>>            port_lmc:        0x00
>>
>>        port:    2
>>            state:            PORT_ACTIVE (4)
>>            max_mtu:        2048 (4)
>>            active_mtu:        2048 (4)
>>            sm_lid:            10
>>            port_lid:        9
>>            port_lmc:        0x00
>>
>>
>> I haven't done any specific configuration for multi-port. I assume that
>> OFED1.3 can do it automatically.
>>
>> Would please any one help me on this?
>>
>> Regards,
>> Jie
>>
>> --
>> Jie Cai
>>
>>
>>
>> _______________________________________________
>> general mailing list
>> general at lists.openfabrics.org
>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/general
>>
>> To unsubscribe, please visit 
>> http://openib.org/mailman/listinfo/openib-general
>>     
> >