[ofw] Windows v .614 doesn't detect IPoIB devices

Woodruff, Robert J robert.j.woodruff at intel.com
Fri Jun 1 16:48:31 PDT 2007


http://www.openfabrics.org/~woody/WinOF_1.0/

________________________________

From: ofw-bounces at lists.openfabrics.org
[mailto:ofw-bounces at lists.openfabrics.org] On Behalf Of Jeremy Enos
Sent: Friday, June 01, 2007 4:46 PM
To: Smith, Stan
Cc: ofw at lists.openfabrics.org
Subject: Re: [ofw] Windows v .614 doesn't detect IPoIB devices


Feeling dumb for asking, but where would I get the WinOF install
package?  I can't find any mention of it in SVN or the Wiki.
thx-

    Jeremy

Smith, Stan wrote: 

	The WinOF 1.0 install package addresses your cluster
requirements in execution and documentation (Release Notes).
	 
	stan.

________________________________

	From: ofw-bounces at lists.openfabrics.org
[mailto:ofw-bounces at lists.openfabrics.org] On Behalf Of Jeremy Enos
	Sent: Thursday, May 31, 2007 1:00 PM
	To: Jan Bottorff
	Cc: ofw at lists.openfabrics.org
	Subject: Re: [ofw] Windows v .614 doesn't detect IPoIB devices
	
	
	Offline, I was just making a similar point.  I didn't mention
it, but I was doing this upgrade interactively (and of course expected
everything to just work).   I was only doing this upgrade interactively
because I haven't built my cluster yet from this 'golden client'.
Future upgrades will need to be non-interactive, which really needs to
be an option for any installer utility as well.  Particularly with
respect to the nature of IB users...  I estimate convenient,
non-interactive needs to be very typical.  I look forward to the day
that there is a reliable installer/updater with both interactive and
non-interactive modes made available.
	
	    Jeremy
	
	Jan Bottorff wrote: 

		That sounds a lot like the symptoms of the IB
coinstaller DLL not
		getting updated with the new build. My experience has
been, coinstallers
		don't get updated with the latest version automatically
by an INF file.
		You need to get an install application to handle this.
It only shows up
		when you are upgrading a system with an older
incompatible coinstaller.
		Putting something in the release notes might be good. My
general policy
		is: there is no assurance than an upgrade between
periodic builds will
		work correctly. Upgrades between official releases will
need to be
		tested as working.
		
		- Jan
		
		-----Original Message-----
		From: ofw-bounces at lists.openfabrics.org
		[mailto:ofw-bounces at lists.openfabrics.org] On Behalf Of
Jeremy Enos
		Sent: Wednesday, May 30, 2007 2:43 PM
		To: ofw at lists.openfabrics.org
		Subject: Re: [ofw] Windows v .614 doesn't detect IPoIB
devices
		
		I think I may have cured this on my own... checked the
driver version 
		for the Infiniband Fabric device, and it did not get
updated with the 
		HCA (was still at 432, which apparently worked fine w/
HCA driver 
		version 459).  Once I forced the Infiniband Fabric
device to update to 
		.614, the IPoIB devices appeared.
		
		    Jeremy
		
		Jeremy Enos wrote:
		  

			So I'm putting together a windows image using
version 614 of openib 
			drivers.  Last time I did this, I was using
version 459, and when the 
			HCA driver was loaded, two IPoIB devices popped
up and needed drivers 
			loaded too.  The HCA driver for v 614 detects
and loads fine, as well 
			as the "Infiniband Fabric" found under System
devices.  However, no 
			new devices are detected for IPoIB.  The event
log is pretty clean 
			too... just 2 informational (blue flag) entries
for the mthca driver 
			loading.
			My operating system is Windows Compute Cluster
x64, using a Dell 1855 
			blade with a daughter card HCA (Infinihost III
pci-e based, using DLGL
			    

		
		  

			4.7.600 fw).
			I have read in some list threads that this
behavior can be due to an 
			out of date firmware, and I should check w/ my
vendor for an updated 
			version.  However, I think I've got the latest
fw offered by my 
			vendor, and as well I've heard reports that this
fw version and same 
			daughter card have worked fine for someone else
with driver version
			    

		614.
		  

			So what should I do next to solve this issue?
			thx-
			
			   Jeremy Enos
			   NCSA
			
			_______________________________________________
			ofw mailing list
			ofw at lists.openfabrics.org
	
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
			    

		_______________________________________________
		ofw mailing list
		ofw at lists.openfabrics.org
	
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
		  

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openfabrics.org/pipermail/ofw/attachments/20070601/e784b1a6/attachment.html>


More information about the ofw mailing list