[ofw] Cannot start SRP initiator

[Erez Cohen]

Erez,

What target are you using? 

Best regards, 

Erez Cohen
Field Application 
Development Manager

Mellanox Technologies Ltd. 
Tel : + 972 - 4 - 9097200 ext 378
Cell : + 972 - 54 - 5468801
Fax : + 972 - 4 - 9593245
www.mellanox.com 

-----Original Message-----
From: ofw-bounces at lists.openfabrics.org
[mailto:ofw-bounces at lists.openfabrics.org] On Behalf Of Erez Zilber
Sent: Wednesday, May 30, 2007 12:06 PM
To: Tzachi Dar
Cc: ofw at lists.openfabrics.org
Subject: Re: [ofw] Cannot start SRP initiator

Tzachi Dar wrote:

>  
>
>   
>> -----Original Message-----
>> From: Erez Zilber [mailto:erezz at voltaire.com]
>> Sent: Tuesday, May 29, 2007 7:13 PM
>> To: Tzachi Dar
>> Cc: ofw at lists.openfabrics.org
>> Subject: Re: [ofw] Cannot start SRP initiator
>>
>> I'm using WinIB from Mellanox's site. I don't know if it's a 
>> free/checked build. I could not find hklm\system\current control 
>> set\services\srp.
>>     
> The default build that you have is free. In order to have a checked 
> build you can do one of the following;
> 1) build it your self :-)
> 2) go to the same page on the Mellanox site and you fill find a zip 
> file with symbols. This file contains all the checked binaries as well

> so you can copy srp.sys from the checked directory to the 
> system32\drivers directory.
>
>
>   
It seems that the path has changed to hklm\system\current control
set\services\ibsrp\Parameters. I can see it now. The current values are:

DebugFlags = ffffff
DebugLevel = 2

What should I put there in order to see the required logs?

BTW - maybe it's a good idea to put this info in the SRP wiki page.
>> Also, I found the following in the release notes:
>>
>>
>> To complete the SRP driver installation, an SRP target must be 
>> detected and a Subnet Manager must be running in the subnet.
>>
>> Upon the detection of an SRP target, the "New Hardware Found" 
>> Wizard pops up.
>>     

I can see "Mellanox referenced SRP target" under "SCSI and RAID
controllers" in the device manager. Does it mean that the initiator
machine "sees" the SRP target? Anyway, it has the following error:

Windows cannot start this hardware device because its configuration
information (in the registry) is incomplete or damaged. (Code 19)

Again, please tell me what should I do in order to supply more info
about it.

>> - Select Install Automatically and click Next. This installs the I/O 
>> unit
>>   device.
>>
>> Once completed, the "New Hardware Found" Wizard pops up again.
>> - Select Install Automatically and click Next. This installs the SRP 
>> driver.
>>
>> I can ping my srpt machine over IPoIB. However, I didn't get any "New

>> Hardware Found" Wizard.
>> Did I miss anything?
>>     
>
> Are you using windows xp32 bit? SRP doesn't work there.
>   

No, I'm using win 2003
> If not, can you go to the device manager and do scan for HW changes?
> This should help.
> If this doesn't help than your problem is probably at the bus driver 
> at the code that should create the virtual device and not at the SRP 
> itself that is not loaded.

_______________________________________________
ofw mailing list
ofw at lists.openfabrics.org
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw