***SPAM*** Re: ***SPAM*** Re: [ofw] Expose a vendor defined device in ibbus?
Deepak Gupta
deepak.gupta at qlogic.com
Thu Jan 29 07:39:20 PST 2009
Leonid,
Thanks for the feedback. Please see the inline below.
On Thu, Jan 29, 2009 at 7:04 PM, Leonid Keller <leonid at mellanox.co.il>wrote:
> [I'm sure missing here something. Could you elaborate more on usage of
> these virtual adapters ? TIA]
>
> BTW, if you are going to create IOC devices (from application but) on
> base of ibiou.sys discovery, why wouldn't you do the same without
> application ?
> Let ibiou.sys creates IOC per HCA for every discovered device...
>
The part we want to achieve with the suggested patch, IOCTL support and an
application is give the user control on what devices they want to have
created and how they want to create them (i.e with which IOC they want to
create a device)
1. If I have 4 IOCs on my fabric, with current IBIOU behavior it
will create 4 devices on all of my nodes.
I might not want all my nodes to use all the IOCs. I might want
a few nodes to use one IOC and few nodes
to use other IOC - essentially load balancing the nodes of my
fabric between IOCs.
For example if I have two Virtual Ethernet I/O gateway devices
in my fabric each with two I/O controllers.
Even though I might not want it, I will have 4 network devices
on each of my nodes consuming resources both
on the nodes and more importantly much more resources (4 times
number of nodes) on the gateway device
2. Some times I might want to create multiple devices with the same
IOC - which is not possible currently.
One of the reasons why I might want to create two devices on the
same IOC is, with VNIC, I might want two virtual
network adapters connected to the same physical network behind
the IOC in case of Virtual Ethernet I/O
gateway controllers (like QLogic EVIC). I would do this to use
load balancing between these two Virtual network
controllers.
Similarly for SRP, I might want to create two virtual HBA
adapters by connecting to the same IOC of the
Virtual Fibre channel gateway controller (like QLogic FVIC) and
I have the controller configured to connect
each adapter with a different storage device based on the
initiator extension of the virtual HBA adapter.
>
> ------------------------------
> *From:* mailmeatdkg at gmail.com [mailto:mailmeatdkg at gmail.com] *On Behalf Of
> *Deepak Gupta
> *Sent:* Thursday, January 29, 2009 2:47 PM
> *To:* Leonid Keller
> *Cc:* ofw at lists.openfabrics.org
> *Subject:* Re: ***SPAM*** Re: [ofw] Expose a vendor defined device in
> ibbus?
>
> Leonid,
>
> I understand you might be busy with some other stuff too.
>
> As I already said, this was just a first draft patch and there are no
> intentions to move it into the svn repository.
> I am sorry, I guess I misled you by asking the question "whether above
> patch is acceptable".
>
> This patch was just to show a use case of having multiple child devices
> associated with a IOC instead of having a single
> child PDO for each IOC.
>
> Plan is to provide a IOCTL interface in ibiou for creation of child devices
> and all device information will be passed through device
> IOCTLs (and not INF file, in this first draf patch I used INF file for just
> POC). So no one has to know the IOC parameters at the time of installation.
>
> It indeed raise the need of a user application which can scan the fabric
> and provide list the of reachable IOCs (particularly Port to IOC path, like
> *ibsrpdm* and *ib_qlgc_vnic_query* tools on linux do).
> I am thinking of providing a IOCTL in ibiou to return the list of reachable
> IOCs.
> Having a list of reachable IOCs with the user, now user can write a
> configuration file describing the child devices (or a GUI to enter the child
> device descriptions). This user application will parse the configuration
> file and will create the device interfaces.
> Also it will record the all these descriptions into registry so that from
> the next boot, ibiou will create the devices without the intervention of
> user app.
>
> >> - having configured one node, one has to repeate all this work with
> all the others or to prepare and clone the image;
>
> Once a node has been configured with a config file, that can be used on
> other nodes too.
>
> >> - if a new IOC has been added, one has to go through all the nodes
> and to change the Registries. It may also require reimaging of all the
> nodes;
>
> If a new IOC has been added, then yes he would need to make entries into
> config file and then user app will take care of rest.
>
> >> - what will happen during the WINOF package upgrade ? We don't want
> user to repeat all this configuration work, do we ?
>
> We will have to provide a versioning on above mentioned device IOCTLs
> interface of ibiou. Minimal release changes will not affect the config file
> structure and hence from a user perspective reconfiguration will not be
> required.
>
> This User Application will help create multiple child devices for ULP's
> (SRP/VNIC) and hence much more failover configurations for the user.
>
> My basic question is if we agree to above then I can move ahead for
> implmenting above mentioned device IOCTLs in ibiou
> and also start doing work on the developing the user application to do
> this.
>
> Please let me know if you have any further queries on it.
>
> Regards
> Deepak
>
>
> On Thu, Jan 29, 2009 at 3:27 PM, Leonid Keller <leonid at mellanox.co.il>wrote:
>
>> Hi Deepak,
>>
>> Sorry for that late reaction. Could not find time beforehand to look into
>> it... :(
>>
>> I'm not sure, whether the advantages of your patch are worth the
>> deployment problems that it can cause (IMO).
>> Here are several ones at the first look:
>> - one has to know all the IOC parameters at the time of installation;
>>
>
>
>> And what if they are yet unknown (IOCs still not purchased) or
>> unknown to the guy (he doesn't know what IOC at all is) ? :(
>> - one has to enter IOC parameters during the installation in some
>> way;
>> Changing INF file is not a convenient way. One has to provide
>> some GUI to edit the parameters during- and the Registry after the
>> installation;
>> - having configured one node, one has to repeate all this work with
>> all the others or to prepare and clone the image;
>> - if a new IOC has been added, one has to go through all the nodes
>> and to change the Registries. It may also require reimaging of all the
>> nodes;
>> - what will happen during the WINOF package upgrade ? We don't want
>> user to repeat all this configuration work, do we ?
>>
>> What do you think ?
>>
>> ------------------------------
>> *From:* ofw-bounces at lists.openfabrics.org [mailto:
>> ofw-bounces at lists.openfabrics.org] *On Behalf Of *Deepak Gupta
>> *Sent:* Tuesday, January 27, 2009 5:19 PM
>> *To:* ofw at lists.openfabrics.org
>> *Subject:* ***SPAM*** Re: [ofw] Expose a vendor defined device in ibbus?
>>
>>
>> Since I didn't receive any concrete response from the list about the
>> patch, I still have following questions unanswered:--
>>
>> 1) I would like to know who is current owner of ibiou and get a feedback
>> on whether above patch is acceptable.
>> Or Do you suggest some modifications on it ?
>>
>> 2) If we are ok with this patch then what time frame should we set for it.
>> Should we target it for coming 2.1 release or for post 2.1 releases?
>>
>> 3) Also, I want to move ahead for implementing IOCTL layer in ibiou for
>> creation of child devices and IOC listings on user request. Is it acceptable
>> to implement this IOCTL layer for device creations and IOC listings in ibiou
>> and you suggest to achieve the same through some other means?
>>
>>
>> *I want to reiterate the purpose of this patch:--*
>>
>> This patch is for creating multiple PDO's for a HCA to IOC path as
>> configured by the user in INF file.
>> It will help in having multiple sessions with the IOC and hence will give
>> some user configurations for fail over.
>>
>> *Behavior change from current ibiou implementation:--*
>>
>> Currently ibiou simply discovers the IOCs and creates child devices for
>> the IOCs discovered.
>> This patch will create multiple child devices for HCA to IOC paths as
>> configured by the user in INF file.
>> If there are no child device configurations for a particular IOC then no
>> devices will be created for that IOC and hence will not appear in device
>> manager's device tree.
>>
>> This is just a first draft patch to show the usability and we have plans
>> to implement IOCTLs in ibiou for child device creations and for listing the
>> reachable IOC PATHs so that a user application can be written which can list
>> the IOCs and local HCAs to the user and user can send IOCTLs to create
>> devices for the ULPs.
>>
>>
>> Regards
>> Deepak
>>
>>
>>
>>
>> On Tue, Jan 27, 2009 at 7:09 PM, Deepak Gupta <deepak.gupta at qlogic.com>wrote:
>>
>>> Forgot to include the list.
>>>
>>> Regards
>>> Deepak
>>>
>>> ---------- Forwarded message ----------
>>> From: Deepak Gupta <deepak.gupta at qlogic.com>
>>> Date: Sat, Jan 24, 2009 at 5:07 PM
>>> Subject: Re: [ofw] Expose a vendor defined device in ibbus?
>>> To: Fab Tillier <ftillier at windows.microsoft.com>
>>>
>>>
>>> Fab, Nice to see your response.
>>> Please see below.
>>>
>>> On Fri, Jan 23, 2009 at 11:09 PM, Fab Tillier <
>>> ftillier at windows.microsoft.com> wrote:
>>>
>>>> I don't have time to look at this in depth, but I can tell you from
>>>> past experience that having a single PDO for an IOC leads to trouble if you
>>>> ever have multiple HCAs in the system. If you have a miniport driver (like
>>>> NDIS or StorPort), the port driver takes care of DMA mappings of
>>>> user-provided buffers. That DMA mapping goes down to the PCI driver for the
>>>> particular HCA, so you could potentially have a mapping that isn't valid for
>>>> one of the multiple HCAs in the system. It's best IMO to have a PDO per IOC
>>>> per HCA (this allows automatic path migration to work in multi-port HCAs),
>>>> and push failover between IOCs to a higher level (LBFO/MPIO).
>>>>
>>>
>>> I had the same concern while implementing the patch.
>>> So I tried to dig into the stack till h/w drivers and it came to me that
>>> all DMA mappings are being
>>> handled by PCI driver.
>>> So this patch creates PDO's per IOC per HCA.
>>> User can specify the child device descriptions in INF file (later on we
>>> can think of having a IOCTL interface in ibiou) and HCA to IOC path.
>>> ibiou will create child PDO's only if HCA to IOC path is present.
>>>
>>> Any more suggestions are welcome!!!
>>>
>>> Regards
>>> Deepak
>>>
>>>
>>>>
>>>>
>>>> -Fab
>>>>
>>>>
>>>>
>>>> *From:* mailmeatdkg at gmail.com [mailto:mailmeatdkg at gmail.com] *On Behalf
>>>> Of *Deepak Gupta
>>>> *Sent:* Friday, January 23, 2009 6:41 AM
>>>> *To:* James Yang
>>>> *Cc:* Leonid Keller; Fab Tillier; ofw at lists.openfabrics.org
>>>>
>>>> *Subject:* Re: [ofw] Expose a vendor defined device in ibbus?
>>>>
>>>>
>>>>
>>>> Did any one get the chance to have a look at the patch?
>>>>
>>>> I am really concerned with the tight coupling of representing each
>>>> single IOC as a single PDO.
>>>>
>>>> Regards
>>>> Deepak
>>>>
>>>>
>>>> On Wed, Jan 21, 2009 at 5:55 PM, Deepak Gupta <deepak.gupta at qlogic.com>
>>>> wrote:
>>>>
>>>> All,
>>>>
>>>> Based on James patch of creating user defined devices tied to local HCA
>>>> ports, I have created a first draft patch attached herewith
>>>> to allow "ibiou" to create user defined devices which will associate
>>>> with IOC paths.
>>>>
>>>> This patch does the following:-
>>>>
>>>> Now ibiou will not create child devices on it's own when it discovers a
>>>> IOC.
>>>> Instead it will create child devices only when it is instructed to do
>>>> so.
>>>> For the sake of this patch, currently it uses name/description of the
>>>> devices hard coded into INF file of ibiou driver.
>>>> Later on we can implement a IOCTL to pass this information to the driver
>>>> (more below)
>>>>
>>>> It will make a listing of devices to be created in it's DriverEntry
>>>> routine.
>>>> When it will get IOC_PNP_ADD pnp events, it will check in device list
>>>> prepare
>>>> earlier. If it finds device(s) in it's list which corresponds to the new
>>>> IOC
>>>> discovered then it will create those child devices and a similar
>>>> mechanism
>>>> will happen when ibiou will get IOC_PNP_ADD event.
>>>>
>>>> This more of a initial patch for giving an insight into what we want to
>>>> achieve.
>>>> On a longer run we are thinking of providing a IOCTL support in ibiou
>>>> driver for creating child devices (like vnic/srp/etc) and
>>>> differnet vendor specific applications can create those devices and have
>>>> their driver loaded on top of that.
>>>>
>>>> Following is the advantage of this functionality:-
>>>>
>>>> Earlier there was only one device created per IOC on host side.
>>>> Now there can be multiple devices on host side per IOC as configured
>>>> in the registry.
>>>> It will be many to one function i.e there can be many devices on host
>>>> side which will target to the same IOC.
>>>> It will be like having different sessions with the same IOC.
>>>>
>>>> Please have a look at it and let me know of your
>>>> comments/suggestions/feeback.
>>>>
>>>> NOTE--> Device descriptions in the INF file of this patch creates
>>>> devices that corresponds to a IOC PATH (CAGUID and IOCGUID).
>>>> Those values are local to my machine and you should change it
>>>> according to your fabric.
>>>>
>>>> Regards
>>>> Deepak
>>>>
>>>>
>>>> On Tue, Jan 20, 2009 at 1:37 AM, James Yang <jyang at xsigo.com> wrote:
>>>>
>>>> The proposal is to use registry key to define vendor devices, and the
>>>> registry key is global to the driver. The assumption is that multiple HCA
>>>> cards will have the same vendor defined devices. It cannot support one HCA
>>>> with vendor-A device, and the other HCA with vendor-B device, in the same
>>>> system. At default all hcas will have IPoIB as child devices.
>>>>
>>>>
>>>>
>>>> Thanks,
>>>>
>>>> James
>>>>
>>>>
>>>> ------------------------------
>>>>
>>>> *From:* Leonid Keller [mailto:leonid at mellanox.co.il]
>>>> *Sent:* Sunday, January 18, 2009 5:57 AM
>>>> *To:* James Yang; Deepak Gupta; Fab Tillier
>>>>
>>>>
>>>> *Cc:* ofw at lists.openfabrics.org
>>>> *Subject:* RE: [ofw] Expose a vendor defined device in ibbus?
>>>>
>>>>
>>>>
>>>> After first look: why did you put the list of the created devices into
>>>> Globals (and not, say, FDO) ?
>>>>
>>>> How it will work for multi-home machine ? (several HCA cards)
>>>>
>>>> Would anybode like to check it for various partition keys ?
>>>>
>>>>
>>>> ------------------------------
>>>>
>>>> *From:* ofw-bounces at lists.openfabrics.org [mailto:
>>>> ofw-bounces at lists.openfabrics.org] *On Behalf Of *James Yang
>>>> *Sent:* Tuesday, January 06, 2009 10:11 PM
>>>> *To:* Deepak Gupta; Fab Tillier
>>>> *Cc:* ofw at lists.openfabrics.org
>>>> *Subject:* RE: [ofw] Expose a vendor defined device in ibbus?
>>>>
>>>> Hi,
>>>>
>>>>
>>>>
>>>> Please review the patch to create user defined devices by reading from
>>>> registry. By default there is only one IpoIB device enabled in mlx4_hca.inx
>>>> file. This patch will only work for ConnectX.
>>>>
>>>>
>>>>
>>>> The paritition key if set to default to FFFF, I didn't test on other
>>>> value. And the Ioctl part to add partition key may also need to be verified.
>>>>
>>>>
>>>>
>>>> Thanks,
>>>>
>>>> James
>>>>
>>>>
>>>>
>>>>
>>>> ------------------------------
>>>>
>>>> *From:* mailmeatdkg at gmail.com [mailto:mailmeatdkg at gmail.com] *On Behalf
>>>> Of *Deepak Gupta
>>>> *Sent:* Monday, January 05, 2009 10:51 PM
>>>> *To:* Fab Tillier
>>>> *Cc:* Tzachi Dar; James Yang; ofw at lists.openfabrics.org
>>>> *Subject:* Re: [ofw] Expose a vendor defined device in ibbus?
>>>>
>>>>
>>>>
>>>> Have a gr8 New Year to all the members!!!.
>>>>
>>>> Do you we any updates on "vendor defined device in ibbus"?
>>>>
>>>> I wanted to create multiple vnic interfaces irrespective of number of
>>>> reachable IOCs.
>>>>
>>>> Currently I am creating vnic child devices on "root" bus.
>>>> Inside VNIC driver, I am looking for arrival GUID_IB_AL_INTERFACE and
>>>> hence contacting the IBAL.
>>>> But since vnic devices are root enumerated, VNIC driver gets loaded very
>>>> earlier in boot phase (Before "Extended Base" group to which IB Stack
>>>> drivers belong) and hence VNIC device interfaces are not getting initialized
>>>> properly.
>>>>
>>>> If we are providing a vendor defined device functionality in ibbus in
>>>> near future, then it would be worth for me to wait for it.
>>>>
>>>> Can any one please comment on this.
>>>>
>>>> Regards
>>>> Deepak
>>>>
>>>> On Mon, Dec 22, 2008 at 1:12 PM, Deepak Gupta <deepak.gupta at qlogic.com>
>>>> wrote:
>>>>
>>>> All,
>>>>
>>>> I came across one more question in my mind which are I think is not
>>>> clear to me after reading the whole thread.
>>>>
>>>> In new design being discussed:-
>>>> Are we making sure that we can have more than one child devices
>>>> configured for the same IOC.
>>>> Currently, there is one child device created per IOC discovered.
>>>>
>>>> Having more than one child device configured for same IOC is a
>>>> requirement if a user wants two different ULP interfaces to be created on
>>>> host side.
>>>> Consider a case in which a host is connected to a single IOC and IOC is
>>>> connected to a ethernet network via switch.
>>>> If there are two different IP subnets then there is a requirement of two
>>>> different Ethernet interfaces on the host side too.
>>>>
>>>> Please let me know if you need more clarification of my question.
>>>>
>>>> Regards
>>>> Deepak
>>>>
>>>>
>>>>
>>>> On Sat, Dec 20, 2008 at 2:19 PM, Deepak Gupta <deepak.gupta at qlogic.com>
>>>> wrote:
>>>>
>>>> Please see below.
>>>>
>>>> Regards
>>>> Deepak
>>>>
>>>> On Sat, Dec 20, 2008 at 12:42 AM, Fab Tillier <
>>>> ftillier at windows.microsoft.com> wrote:
>>>>
>>>> > On Wed, Dec 17, 2008 at 11:43 PM, Fab Tillier
>>>> > <ftillier at windows.microsoft.com> wrote:
>>>>
>>>> >> Are there other properties that I have missed that are needed?
>>>> >
>>>> > We need a way in which devices created should be configured for
>>>> > failovers ( ULPs like VNIC, SRP need more configurable failovers).
>>>> > Looking at IBAL's code it create the devices based on the reachable
>>>> > IOC's and thus failover's are possible across the HCA/ports and not
>>>> > across two different IOCs.
>>>> > Users can have a case in which two different IOCs connected to same
>>>> > physical network/storage (redundancy is provided for high
>>>> availability)
>>>> > and want a failover across the IOCs.
>>>>
>>>> This would be done via LBFO for network devices, and MPIO for storage
>>>> devices. I think having the bus driver report a single IOC that really maps
>>>> to two IOCs on the fabric is asking for management problems. Further,
>>>> LBFO/MPIO can provide failover between different device types, so the
>>>> failover devices don't have to be identical HW.
>>>>
>>>>
>>>> I don't know about how MPIO works. But for LBFO, BundleID param will
>>>> have to be included in extended params then so that user gets the freedom of
>>>> bundling different failover configurations.
>>>>
>>>>
>>>>
>>>>
>>>> -Fab
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> ofw mailing list
>>>> ofw at lists.openfabrics.org
>>>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> ofw mailing list
>>>> ofw at lists.openfabrics.org
>>>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
>>>>
>>>
>>>
>>>
>>
>> _______________________________________________
>> ofw mailing list
>> ofw at lists.openfabrics.org
>> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
>>
>
>
> _______________________________________________
> ofw mailing list
> ofw at lists.openfabrics.org
> http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ofw
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openfabrics.org/pipermail/ofw/attachments/20090129/71d8b905/attachment.html>
More information about the ofw
mailing list