[Users] IB topology config and polling state

[German Anders]

I'm noticing that the ISL port from the HP IB SW does not had the LLR state
'active' instead is said 'Inactive' and the LLR supported speeds are FDR10,
FDR only, so I try to change the LLR profile in order to support QDR but
when I try to change it, it displays an error msg:
"Cannot map profile hp-encl-isl to port:  1/15"

Any ideas? Maybe that's an issue and because of that the ports are not
coming up? or they supposed to work anyway?


*German* <ganders at despegar.com>

2015-10-07 12:54 GMT-03:00 Weiny, Ira <ira.weiny at intel.com>:

> There are a few issues for routing in that diagram but the links should
> come up.
>
>
>
> I assume there is some backplane between the blade servers and the switch
> in that chassis?
>
>
>
> Have you gotten libipathverbs installed?
>
>
>
> In ipathverbs there is a serdes tuning script.
>
>
>
> https://github.com/01org/libipathverbs/blob/master/truescale-serdes.cmds
>
>
>
> Does your libipathverbs include that file?  If not try the latest from
> github.
>
>
>
> Ira
>
>
>
>
>
> *From:* users-bounces at lists.openfabrics.org [mailto:
> users-bounces at lists.openfabrics.org] *On Behalf Of *German Anders
> *Sent:* Wednesday, October 07, 2015 8:41 AM
> *To:* Hal Rosenstock
> *Cc:* users at lists.openfabrics.org
> *Subject:* Re: [Users] IB topology config and polling state
>
>
>
> Hi Hal,
>
> Thanks for the reply, I've attach a pdf with the diagram topology, I don't
> know if this is the best way to go or if there's another way to connect and
> setup the IB network, tips and suggestions will be very appreciated, also
> the mezzanine cards are already installed on the blade hosts:
>
> # lspci
> (...)
> 41:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02)
>
>
>
> Thanks in advance,
>
> Cheers,
>
>
> *German*
>
>
>
> 2015-10-07 11:47 GMT-03:00 Hal Rosenstock <hal.rosenstock at gmail.com>:
>
> Hi again German,
>
>
>
> Looks like you made some progress from yesterday as the qib ports are now
> Polling rather than Disabled.
>
>
>
> But since they are Down, do you have them cabled to a switch ? That should
> bring the links up and the port state will be Init. That is the "starting"
> point.
>
>
>
> You will also then need to be running SM to bring the ports up to Active.
>
>
>
> -- Hal
>
>
>
> On Wed, Oct 7, 2015 at 10:37 AM, German Anders <ganders at despegar.com>
> wrote:
>
> Hi all,
>
> I don't know if this is the mailist list for this kind of topic but I'm
> really new to IB and I've just install two SX6036G gateways connected to
> each other through two ISL ports, then I've configured a proxy-arp between
> both nodes (sm is disable on both gw's):
>
> GWIB01 [proxy-ha-group: master] (config) # show proxy-arp ha
>
> Load balancing algorithm: ib-base-ip
> Number of Proxy-Arp interfaces: 1
>
> Proxy-ARP VIP
> =============
> Pra-group name: proxy-ha-group
> HA VIP address: 10.xx.xx.xx/xx
>
> Active nodes:
> ID                   State                IP
> --------------------------------------------------------------
> GWIB01               master               10.xx.xx.xx1
> GWIB02               standby              10.xx.xx.xx2
>
> Then I setup two SX6018F switches (*SWIB01* and *SWIB02*), one connected
> to GWIB01 and the other connected to GWIB02. The SM is configured locally
> on both SWIB01 & SWIB02 switches. So far so good, after this config I setup
> a commodity server with a MLNX IB ADPT FDR to the SWIB01 & SWIB02 switches,
> config the drivers, etc and then get it up & running fine.
>
> Finally I've setup a HP Enclosure with an internal IB SW (then connect
> port 1 of the internal SW to GWIB01 - link is up but LLR status is
> inactive), install one of the blades and I see the following:
>
> # ibstat
> CA 'qib0'
>     CA type: InfiniPath_QMH7342
>     Number of ports: 2
>     Firmware version:
>     Hardware version: 2
>     Node GUID: 0x0011750000791fec
>     System image GUID: 0x0011750000791fec
>     Port 1:
>         State: Down
>         Physical state: Polling
>         Rate: 40
>         Base lid: 4660
>         LMC: 0
>         SM lid: 4660
>         Capability mask: 0x0761086a
>         Port GUID: 0x0011750000791fec
>         Link layer: InfiniBand
>     Port 2:
>         State: Down
>         Physical state: Polling
>         Rate: 40
>         Base lid: 4660
>         LMC: 0
>         SM lid: 4660
>         Capability mask: 0x0761086a
>         Port GUID: 0x0011750000791fed
>         Link layer: InfiniBand
>
> So I was wondering if maybe the SM is not being recognized on the Blade
> system and that's why is not passing the Polling state, is that possible?
> Or maybe is not possible to connect an ISL between the GW and the HP
> internal SW so that the sm is available or maybe the inactive LLR is
> causing this thing, any ideas? I thought about connecting the ISL of the
> HP IB SW to the SWIB01 or SWIB02 instead of the GW's but I don't have any
> available ports.
>
> Thanks in advance,
>
> Cheers,
>
>
> *German*
>
>
>
> _______________________________________________
> Users mailing list
> Users at lists.openfabrics.org
> http://lists.openfabrics.org/mailman/listinfo/users
>
>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openfabrics.org/pipermail/users/attachments/20151007/0d3f1244/attachment.html>