[openfabrics-ewg] OFED-1.0-rc6 is available

Sharma, Karun ksharma at silverstorm.com
Thu Jun 8 21:04:33 PDT 2006


Hi Vlad:
 
See below for the output. I performed following steps:
1. After installing RC6 and configuring IB interfaces during the install process, i rebooted the system.
 
2. Then I did ifconfig ib0. It doesn't show the ip address configured during install.
 
3. After that I checked the status of openibd. It was running fine and showing me ib0 and ib1 as active devices.
 
4. Then I restarted openibd. After this restart, I was able to see the IP address of ib0 and ib1 interfaces. 
 
But after reboot we should see the IP addresses and should not restart openibd everytime after reboot.
Now if I again reboot the system, I will lose the ip addresses of IB interfaces. I am able to reproduce it.
 
Thanks,
Karun
 
 
######################################################################################
The system is going down for reboot NOW!
[st44 Thu Jun 08 23:46:44]# Last login: Thu Jun  8 23:46:37 2006 from 192.168.0.62
[st44 Thu Jun 08 23:54:29]# ifconfig ib0
ib0       Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          UP BROADCAST RUNNING MULTICAST  MTU:2044  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:2 overruns:0 carrier:0
          collisions:0 txqueuelen:128 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
[st44 Thu Jun 08 23:54:35]# /etc/init.d/openibd status
  HCA driver loaded
Configured devices:
ib0 ib1
Currently active devices:
ib0
ib1

[st44 Thu Jun 08 23:54:47]# /etc/init.d/openibd restart
Shutting down interface ib0:                               [  OK  ]
Shutting down interface ib1:                               [  OK  ]
Unloading HCA driver:                                      [  OK  ]
Loading HCA driver and Access Layer:                       [  OK  ]
Setting up InfiniBand network interfaces:
Bringing up interface ib0:                                 [  OK  ]
Bringing up interface ib1:                                 [  OK  ]
Setting up service network . . .                           [  done  ]
[st44 Thu Jun 08 23:55:08]# ifconfig ib0
ib0       Link encap:UNSPEC  HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00  
          inet addr:172.26.16.44  Bcast:172.26.16.255  Mask:255.255.240.0
          UP BROADCAST RUNNING MULTICAST  MTU:2044  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:2 overruns:0 carrier:0
          collisions:0 txqueuelen:128 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
[st44 Thu Jun 08 23:55:12]# 
####################################################################

________________________________

From: Vladimir Sokolovsky [mailto:vlad at mellanox.co.il]
Sent: Thu 6/8/2006 9:48 AM
To: Sharma, Karun
Cc: Tziporet Koren; openfabrics-ewg at openib.org
Subject: Re: [openfabrics-ewg] OFED-1.0-rc6 is available



Hi Karun,
I can't reproduce this issue.
Please try '/etc/init.d/openibd restart' and send me the output.

Please check that ifcfg-ib0 located under /etc/sysconfig/network on SuSE and
under /etc/sysconfig/network-scripts on RedHat/Fedora.
Thanks,

Regards,
Vladimir



Sharma, Karun wrote:
> Hi Tziporet:
> 
> At the end of install script, we specify IP addresses for ib0 and ib1
> interfaces. Then i reboot the system. After the system comes back, i
> observed that ip address of ib0 interface (ifconfig ib0) is missing.
> We need to configure again the ip address of ib0 and ib1 interfaces.
> Please let me know if this is a bug. Why do we need to specify same ip
> address twice? I can see the IP address which i configure during
> install time in ifcfg-ib0 file.
> 
> I have seen this behaviour on RHEL4 up2 and FC4 servers. Below are
> some logs.
> 
> Thanks
> Karun
> 
> ################################################################
> 
> [root at ss23 ~]# /etc/init.d/opensmd status
> opensm (pid 3216) is running...
> [root at ss23 ~]# cat /etc/sysconfig/network-scripts/ifcfg-ib0
> DEVICE=ib0
> BOOTPROTO=static
> IPADDR=172.20.51.223
> NETMASK=255.255.255.0
> NETWORK=172.20.0.0
> BROADCAST=172.20.51.255
> ONBOOT=yes
> [root at ss23 ~]# ifconfig ib0
> ib0       Link encap:InfiniBand  HWaddr
> 00:00:00:14:FE:80:00:00:00:00:00:00:00:00:00:00:00:00:00:00
>           inet6 addr: fe80::206:6a00:a000:537/64 Scope:Link
>           UP BROADCAST RUNNING MULTICAST  MTU:2044  Metric:1
>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:128
>           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
> [root at ss23 ~]#
> ##############################################################################


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.openfabrics.org/pipermail/ewg/attachments/20060609/6716c9b9/attachment.html>


More information about the ewg mailing list